View NCP1308DR2G_432822.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

NCP1308 PWM Current-Mode Controller for Free-Running Quasi-Resonant Operation
The NCP1308 combines a true current mode modulator and a demagnetization detector to ensure full borderline/Critical Conduction Mode in any load/line conditions and minimum drain voltage switching (Quasi-Resonant operation). Due to its inherent skip cycle capability, the controller enters burst mode as soon as the power demand falls below a predetermined level. As this happens at low peak current, no audible noise can be heard. An internal 10 ms timer prevents the free-run frequency to exceed a high frequency (therefore below the 150 kHz CISPR-22 EMI starting limit), while the skip adjustment capability lets the user select the frequency at which the burst foldback takes place. The Dynamic Self-Supply (DSS) drastically simplifies the transformer design in avoiding the use of an auxiliary winding to supply the NCP1308. This feature is particularly useful in applications where the output voltage varies during operation (e.g. battery chargers). Thanks to its high-voltage technology, the IC is directly connected to the high-voltage DC rail. As a result, the short-circuit trip point is not dependent upon any VCC auxiliary level. The transformer core reset detection is done through an auxiliary winding which, brought via a dedicated pin. If an OVP is detected on the VCC pin, the IC permanently latches off. Finally, the continuous feedback signal monitoring implemented with an Overcurrent fault Protection circuitry (OCP) makes the final design rugged and reliable.
Features http://onsemi.com MARKING DIAGRAM
8 1 SOIC-8 DR SUFFIX CASE 751 8 1308 ALYW G 1
A L Y W G
= Assembly Location = Wafer Lot = Year = Work Week = Pb-Free Package
PIN CONNECTIONS
Dmg 1 FB 2 CS 3 GND 4 (Top View) 8 HV 7 6 VCC 5 Drv
* * * * * * * * * * * * * * * * * * *
Free-Running Borderline/Critical Mode Quasi-Resonant Operation Current-Mode with Adjustable Skip Cycle Capability Dynamic Self-Supply Type of VCC Auto-Recovery Overcurrent Protection Improved UVLO for VCC below 10 V Latching Overvoltage Protection on VCC 500 mA Peak Current Source/Sink Capability Internal 1.0 ms Soft-Start Internal 10 ms Minimum TOFF Adjustable Skip Level Internal Temperature Shutdown Internal Leading Edge Blanking Direct Optocoupler Connection SPICE Models Available for TRANsient Analysis This is a Pb-Free Device AC-DC Adapters for Notebooks, etc. Offline Battery Chargers Consumer Electronics (DVD Players, Set-Top Boxes, TVs, etc.) Auxiliary Power Supplies (USB, Appliances, TVs, etc.)
1
ORDERING INFORMATION
Device NCP1308DR2G Package SOIC-8 (Pb-Free) Shipping 2500/T ape & Reel
For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D.
Typical Applications
(c) Semiconductor Components Industries, LLC, 2005
December, 2005 - Rev. 2
Publication Order Number: NCP1308/D
NCP1308
R* + 12 V @ 1 A GND
NCP1308
+ 1 Universal Network 2 3 4 8 7 6 5
+
*Please refer to the application information section.
Y1 Type
Figure 1. Typical Application Schematic
PIN FUNCTION DESCRIPTION
Pin 1 2 Symbol Dmg FB Function Core reset detection Sets the peak current setpoint Description The auxiliary FLYBACK signal ensures discontinuous operation. By connecting an optocoupler to this pin, the peak current setpoint is adjusted accordingly to the output power demand. By bringing this pin below the internal skip level, the device shuts off. This pin senses the primary current and routes it to the internal comparator via an LEB By inserting a resistor in series with the pin, you control the level at which the skip operation takes place. - The driver's output to an external MOSFET. This pin is connected to an external bulk capacitor of typically 10 mF. If an auxiliary winding brings this pin above 16 V typical, the circuit permanently latches off. This unconnected pin ensures adequate creepage distance. Connected to the high-voltage rail, this pin injects a constant current into the VCC bulk capacitor.
3
CS
Current sense input and skip cycle level selection The IC ground Driving pulses Supplies the IC - High-voltage pin
4 5 6 7 8
GND Drv VCC NC HV
http://onsemi.com
2
NCP1308
50 us Filter 7 mA + + 16 V + 12 V 10 V 5.3 V (Fault) + OVP S S R PON Dmg
VUVLO + 10 us Blanking + 50 mV
+
HV
+ - Resd Dmg
10 V
Q Q R Driver src = 20 sink = 10 To internal supply 20k Drv
VCC
To Internal Supply
Fault Mngt. + -
Soft-Start = 1 ms /3 1V 200 mA when DRV is OFF Time Reset Dmg 380 ns LEB
FB
GND
Overload? 5 us Timeout
CS
Figure 2. Internal Circuit Architecture
MAXIMUM RATINGS
Rating Power Supply Voltage Maximum Voltage on all other pins except Pin 8 (HV), Pin 6 (VCC) and Pin 5 (Drv) and Pin 1 (Dmg) Maximum Current into all pins except VCC (6), HV (8) and Dmg (1) when 10 V ESD diodes are activated Maximum Current in Pin 1 Thermal Resistance, Junction-to-Case Thermal Resistance, Junction-to-Air Maximum Junction Temperature Temperature Shutdown Hysteresis in Shutdown Storage Temperature Range ESD Capability, Human Body Model (All pins except HV) ESD Capability, Machine Model Maximum Voltage on Pin 8 (HV), Pin 6 (VCC) Decoupled to Ground with 10 mF Minimum Voltage on Pin 8 (HV), Pin 6 (VCC) Decoupled to Ground with 10 mF Symbol VCC, Drv - - Idem RqJC RqJA TJMAX - - - - - VHVMAX VHVMIN Value 20 -0.3 to 10 5.0 +3.0/-2.0 57 178 150 155 30 -60 to +150 2.0 200 500 40 Unit V V mA mA C/W C/W C C C C kV V V V
Maximum ratings are those values beyond which device damage can occur. Maximum ratings applied to the device are individual stress limit values (not normal operating conditions) and are not valid simultaneously. If these limits are exceeded, device functional operation is not implied, damage may occur and reliability may be affected.
http://onsemi.com
3
NCP1308
ELECTRICAL CHARACTERISTICS (For typical values TJ = 25C, for min/max values TJ = 0C to +125C, Max TJ = 150C,
VCC = 11 V unless otherwise noted.) Characteristic DYNAMIC SELF SUPPLY VCC Increasing Level at which the Current Source Turns-Off VCC Decreasing Level at which the Current Source Turns-On VCC Decreasing Level at which the Latchoff Phase Ends VCC Level at which pulses are disabled Internal IC Consumption, No Output Load on Pin 5, FSW = 60 kHz Internal IC Consumption, 1.0 nF Output Load on Pin 5, FSW = 60 kHz Internal IC Consumption, Latchoff Phase, VCC = 6.0 V INTERNAL STARTUP CURRENT SOURCE ( TJ = 0C) High-Voltage Current Source, VCC = 10 V High-Voltage Current Source, VCC = 0 DRIVE OUTPUT Output Voltage Rise-Time @ CL = 1.0 nF, 10-90% of Output Signal Output Voltage Fall-Time @ CL = 1.0 nF, 10-90% of Output Signal Source Resistance Sink Resistance CURRENT COMPARATOR Input Bias Current @ 1.0 V Input Level on Pin 3 Maximum Internal Current Setpoint Propagation Delay from Current Detection to Gate OFF State Leading Edge Blanking Duration Internal Current Offset Injected on the CS Pin During OFF Time OVERVOLTAGE SECTION Voltage on the VCC above which the controller latches off Integration Time Constraint on the OVP comparator FEEDBACK SECTION (VCC = 11 V, Pin 5 loaded by 1.0 kW) Internal Pullup Resistor Pin 3 to Current Setpoint Division Ratio Internal Soft-Start DEMAGNETIZATION DETECTION BLOCK Input Threshold Voltage (Vpin 1 Decreasing) Hysteresis (Vpin 1 Decreasing) Input Clamp Voltage High State (Ipin 1 = 3.0 mA) Low State (Ipin 1 = -2.0 mA) Dmg Propagation Delay Internal Input Capacitance at Vpin 1 = 1.0 V Minimum TOFF (Internal Blanking Delay After TON) Timeout After Last Dmg Transition 1. Max value at TJ = 0C, please see characterization curves. 1 1 1 1 1 1 1 1 Vth VH VCH VCL Tdem Cpar Tblank Tout 35 - 8.0 -0.9 - - - - 50 20 10 -0.7 210 10 10 5.0 90 - 12 -0.5 - - - - ns pF ms ms mV mV V 2 - - Rup Iratio Tss - - - 20 3.3 1.0 - - - kW - ms 6 6 VOVP Tint 14.3 - 16 50 17.8 - V ms 3 3 3 3 3 IIB ILimit TDEL TLEB Iskip - 0.92 - - - 0.02 1.0 100 380 200 - 1.12 160 - - mA V ns ns mA 5 5 5 5 Tr Tf ROH ROL - - 12 5.0 40 20 20 10 - - 36 20 ns ns W W 8 8 IC1 IC2 4.3 - 7.0 8.0 9.6 - mA mA 6 6 6 6 6 6 6 VCCOFF VCCON VCClatch VUVLO ICC1 ICC2 ICC3 10.8 9.1 - - - - - 12 10 5.3 VCCON - 200 mV 1.0 1.6 330 12.9 10.6 - - 1.3 (Note 1) 2.0 (Note 1) - V V V V mA mA mA Pin Symbol Min Typ Max Unit
http://onsemi.com
4
NCP1308
TYPICAL CHARACTERISTICS
120 100 80 VTH, (mV) 60 40 20 0 -25 Ilimit, (V) 1.20 1.15 1.10 1.05 1.00 0.95 0.90 -25
0
25
50
75
100
125
0
25
50
75
100
125
TEMPERATURE (C)
TEMPERATURE (C)
Figure 3. Demagnetization Threshold vs. Temperature
18 18 17 ICC1, (mA) VCC, (V) 17 16 16 15 -25 1.60 1.40 1.20 1.00 0.80 0.60 0.40 -25
Figure 4. Maximum Peak Current Setpoint vs. Temperature
0
25
50
75
100
125
0
25
50
75
100
125
TEMPERATURE (C)
TEMPERATURE (C)
Figure 5. OVP Level Threshold vs. Temperature
Figure 6. Internal IC Consumption (No Output Load) vs. Temperature
2.00 1.95 1.90 1.85 ICC2, (mA) 1.80 1.75 1.70 1.65 1.60 1.55 1.50 -25 0 25 50 75 100 125
TEMPERATURE (C)
Figure 7. Internal IC Consumption (1.0 nF Load) vs. Temperature
http://onsemi.com
5
NCP1308
TYPICAL CHARACTERISTICS
12.90 11.0 10.8 12.40 VCCOFF, (V) VCCON, (V) 10.6 10.4 11.90 10.2 10.0 9.8 9.6 10.90 9.4 9.2 10.40 -25 0 25 50 75 100 125 9.0 -25 0 25 50 75 100 125
11.40
TEMPERATURE (C)
TEMPERATURE (C)
Figure 8. VCC Increasing Level at which the Current Source Turns-off vs. Temperature
12 11 10 ROH and ROL (W) 9 IC1, (mA) 8 7 6 5 4 3 2 -25 0 25 50 75 100 125 40 35 30 25 20 15 10 5 0 -25
Figure 9. VCC Decreasing Level at which the Current Source Turns-on vs. Temperature
ROH
ROL
0
25
50
75
100
125
TEMPERATURE (C)
TEMPERATURE (C)
Figure 10. Internal Startup Current Source, VCC = 10 V vs. Temperature
Figure 11. Source and Sink Resistance vs. Temperature
http://onsemi.com
6
NCP1308
APPLICATION INFORMATION
INTRODUCTION
The NCP1308 implements a standard current mode architecture where the switch-off time is dictated by the peak current setpoint, whereas the core reset detection triggers the turn-on event. This component represents the ideal candidate where low part-count is the key parameter, particularly in low-cost AC/DC adapters, consumer electronics, auxiliary supplies, etc. Due to its high-performance High-Voltage technology, the NCP1308 incorporates all the necessary components/features needed to build a rugged and reliable Switch-Mode Power Supply (SMPS): * Transformer Core Reset Detection: Borderline/critical operation is ensured whatever the operating conditions are. As a result, there are virtually no primary switch turn-on losses and no secondary diode recovery losses. The converter also stays a first-order system and accordingly eases the feedback loop design. * Quasi-Resonant Operation: By delaying the turn-on event, it is possible to restart the MOSFET in the minimum of the drain-source wave, ensuring reduced EMI/video noise perturbations. In nominal power conditions, the NCP1308 operates in Borderline Conduction Mode (BCM) also called Critical Conduction Mode (CCM). * Dynamic Self-Supply (DSS): Due to its Very High Voltage Integrated Circuit (VHVIC) technology, ON Semiconductor 's NCP1308 allows for a direct pin connection to the high-voltage DC rail. A dynamic current source charges up a capacitor and thus provides a fully independent VCC level to the NCP1308. As a result, there is no need for an auxiliary winding to supply the IC, whose management is always a problem in variable output voltage designs (e.g. battery chargers). * Overvoltage Protection (OVP): By monitoring the VCC pin via a 50 ms time constant filter, the NCP1308 goes into latched fault condition whenever an overvoltage condition is detected. This occurs if VCC goes above 16 V typically. The controller stays fully latched in this position until the VCC is cycled down to 4 V, e.g. when the user unplugs the power supply from the mains outlet and re-plugs it. * Adjustable Skip Cycle Level: By offering the ability to tailor the level at which the skip cycle takes place, the designer can make sure that the skip operation only occurs at low peak current. This point guarantees
*
a noise-free operation with cheap transformer. This option also offers the ability to fix the maximum switching frequency when entering light load conditions. Overcurrent Protection (OCP): By continuously monitoring the FB line activity, NCP1308 enters burst mode as soon as the power supply undergoes an overload. The device enters a safe low power operation that prevents from any lethal thermal runaway. As soon as the default disappears, the power supply resumes operation. Unlike other controllers, overload detection is performed independently of any auxiliary winding level. In presence of a bad coupling between both power and auxiliary windings, the short circuit detection can be severely affected. The DSS naturally shields you against these troubles.
Dynamic Self-Supply
The DSS principle is based on the charge/discharge of the VCC bulk capacitor from a low level up to a higher level. We can easily describe the current source operation with some simple logical equations: POWER-ON: IF VCC < VCCOFF THEN Current Source is ON, no output pulses IF VCC decreasing > VCCON THEN Current Source is OFF, output is pulsing IF VCC increasing < VCCOFF THEN Current Source is ON, output is pulsing Typical values are: VCCOFF = 12 V, VCCON = 10 V To better understand the operational principle, the diagram in Figure 12 offers the necessary light:
Vripple = 2V VCC
VCC OFF 12V =
VCC ON= 10V
CURRENT SOURCE
ON
OFF
Output pulses
Figure 12. The Charge/Discharge Cycle over a 10 mF VCC Capacitor
http://onsemi.com
7
NCP1308
The DSS behavior actually depends on the internal IC consumption and the MOSFET's gate charge Qg. If we select a MOSFET like the MTP2N60E, Qg equals 22 nC (max). With a maximum switching frequency selected at 75 kHz, the average power necessary to drive the MOSFET (excluding the driver efficiency and neglecting various voltage drops) is: FSW @ Qg @ VCC with: FSW = maximum switching frequency Qg = MOSFET's gate charge VCC = VGS level applied to the gate To obtain the output current, simply divide this result by VCC: Idriver + FSW @ Qg + 1.6 mA. The total standby power consumption at no-load will therefore heavily rely on the internal IC consumption plus the above driving current (altered by the driver's efficiency). Suppose that the IC is supplied from a 350 VDC line. The current flowing through Pin 8 is a direct image of the NCP1308 consumption (neglecting the switching losses of the HV current source). If ICC2 equals 2.3 mA @ TJ = 60C, then the power dissipated (lost) by the IC is simply: 350 V x 2.3 mA = 805 mW. For design and reliability reasons, it would be interesting to reduce this source of wasted power that increases the die temperature. This can be achieved by using different methods: 1. Use a MOSFET with lower gate charge Qg 2. Connect a diode to the half-wave portion to directly supply the HV pin:
HV 5 Cbulk 1 MAINS 2 1 2 3 4 8 7 6 5 6 1N4007
Skipping Cycle Mode
The NCP1308 automatically skips switching cycles when the output power demand drops below a given level. This is accomplished by monitoring the FB pin. In normal operation, Pin 2 imposes a peak current accordingly to the load value. If the load demand decreases, the internal loop asks for less peak current. When this setpoint reaches a determined level, the IC prevents the current from decreasing further down and starts to blank the output pulses: the IC enters the so-called skip cycle mode, also named controlled burst operation. The power transfer now depends upon the width of the pulse bunches (Figure 14) and follows the following formula:
1 @ Lp @ Ip2 @ F SW @ Dburst with: 2
Lp = primary inductance FSW = switching frequency within the burst Ip = peak current at which skip cycle occurs Dburst = burst width/burst recurrence
MAX PEAK CURRENT NORMAL CURRENT MODE OPERATION SKIP CYCLE CURRENT LIMIT
CURRENT SENSE SIGNAL (mV)
300
200
100
0 WIDTH RECURRENCE
Figure 14. The Skip Cycle Takes Place at Low Peak Currents which Guarantees Noise-Free Operation
DRIVER DRIVER = HIGH ? I = 0 DRIVER = LOW ? I = 200 mA - + Rskip 3 Rsense 2
Figure 13. The Connection to the Half-Wave Signal Reduces the Dissipated Power on the Controller
RESET
3. Permanently force the VCC level above VCCON with an auxiliary winding. It will automatically disconnect the internal startup source and the IC will be fully self-supplied from this winding. Again, the total power drawn from the mains will significantly decrease. Make sure the auxiliary voltage never exceeds the 16 V limit. When the power supply is switched off, an internal comparator makes sure that all output pulses are disable when VCC crosses VCCON.
+
Figure 15. A Patented Method Allows for Skip Level Selection via a Series Resistor Inserted in Series with the Current
http://onsemi.com
8
NCP1308
The skip level selection is done through a simple resistor inserted between the current sense input and the sense element. Every time the NCP1308 output driver goes low, a 200 mA source forces a current to flow through the sense pin (Figure 15): when the driver is high, the current source is off and the current sense information is normally processed. As soon as the driver goes low, the current source delivers 200 mA and develops a ground-referenced voltage across Rskip. If this voltage is below the feedback voltage, the current sense comparator stays in the high state and the internal latch can be triggered by the next clock cycle. Now, if because of a low load mode the feedback voltage is below Rskip level, then the current sense comparator permanently resets the latch and the next clock cycle (given by the demagnetization detection) is ignored: we are skipping cycles as shown in Figure 15. As soon as the feedback voltage goes up again, there can be two situations: the recurrent period is small and a new demagnetization detection (next wave) signal triggers the NCP1308. To the opposite, in low output power conditions, no more ringing waves are present on the drain and the toggling of the current sense comparator together with the internal 5 ms timeout initiates a new cycle start. In normal operating conditions, e.g. when the drain oscillations are generous, the demagnetization comparator can detect the 50 mV crossing and gives the "green light", alone, to re-active the power switch. However, when skip cycle takes place (e.g. at low output power demands), the restart event slides along the drain ringing waveforms (actually the valley locations) which decays more or less quickly, depending on the Lprimary-Cparasitic network damping factor. The situation can thus quickly occur where the ringing becomes too weak to be detected by the demagnetization comparator: it then permanently stays locked in a given position and can no longer deliver the "green light" to the controller. To help in this situation, the NCP1308 implements a 5 ms timeout generator: each time the 50 mV crossing occurs, the timeout is reset. So, as long as the ringing becomes too low, the timeout generator starts to count and after 5 ms, it delivers its "green light". If the skip signal is already present then the controller restarts; otherwise the logic waits for it to set the drive output high. Figure 16 depicts these two different situations:
Drain Signal
Timeout Signal Dmg Restart Current Sense and Timeout Restart Drain Signal
Timeout Signal
5 ms
5 ms
Figure 16. When the primary natural ringing becomes too low, the internal Timeout together with the sense comparator initiates a new cycle when FB passes the skip level.
http://onsemi.com
9
NCP1308
Demagnetization Detection
The core reset detection is done by monitoring the voltage activity on the auxiliary winding. This voltage features a FLYBACK polarity. The typical detection level is fixed at 50 mV as exemplified by Figure 17.
Figure 19 portrays a typical Vds shot at nominal output power.
400 DRAIN VOLTAGE (V)
7.0 POSSIBLE RESTARTS
300
DMG SIGNAL (V)
5.0
200
3.0
100
1.0 0V
0 50 mV
-1.0
Figure 19. The NCP1308 Operates in Borderline/Critical Operation Overvoltage Protection
Figure 17. Core Reset Detection is Done through a Dedicated Auxiliary Winding Monitoring
An internal timer prevents any restart within 10 s further to the driver going-low transition. This prevents the switching frequency to exceed (1/(TON + 10 ms)) but also avoid false leakage inductance tripping at turn-off. In some cases, the leakage inductance kick is so energetic, that a slight filtering is necessary. The NCP1308 demagnetization detection pad features a specific component arrangement as detailed by Figure 18. In this picture, the Zener diodes network protect the IC against any potential ESD discharge that could appear on the pins. The first ESD diode connected to the pad, exhibits a parasitic capacitance. When this parasitic capacitance (10 pF typically) is combined with Rdem, a restart delay is created and the possibility to switch right in the drain-source wave exists. This guarantees QR operation with all the associated benefits (low EMI, no turn-on losses etc.). Rdem should be calculated to limit the maximum current flowing through Pin 1 to less than +3 mA / -2 mA: if during turn-on, the auxiliary winding delivers -30 V (at the highest line level), then the minimum Rdem value is defined by: (-30 + 0.7. This value will be further increased to introduce a restart delay and also a slight filtering in case of high leakage energy.
TO INTERNAL COMPARATOR
The overvoltage works by monitoring the VCC pin via a comparator and a reference voltage. Figure 20 portrays the internal arrangement:
50 us FILTER VCC
+ 16 V - + OVP COMPARATOR TO LATCH
Figure 20. OVP Section Circuitry
Resd 1 ESD ESD 4
Rdem
A 50 ms time-constant filter prevents any parasitic spikes superimposed on the VCC to adversely trigger the OVP comparator. When the OVP comparator output goes high, the NCP1308 fully latches off and stays latched, being self-supplied by the DSS. The user must unplug the power supply and wait that the VCC comes down below a reset voltage of typically 4 V.
Aux
Figure 18. Internal Pad Implementation
http://onsemi.com
10
NCP1308
Shutting off the NCP1308
Shutdown can easily be implemented through a simple NPN bipolar transistor as depicted by Figure 21. When OFF, Q1 is transparent to the operation. When forward biased, the transistor pulls the FB pin to ground (VCEsat 200 mV) and permanently disables the IC. A small time constant on the transistor base will avoid false triggering
NCP1308 1 10 k ON/OFF Q1 10 nF 2 3 4 8 7 6 5
where IDSS is the peak DSS capability, DSSduty-cycle is the duty-cycle of the DSS, that is to say, the time it is on and the time it stays off (DSSduty-cycle = on/(on + off) ). Please refer to the application note AND8069/D available at www.onsemi.com/pub/ncp1200. If the power consumption budget is really too high for the DSS alone, connect a diode between the auxiliary winding and the VCC pin which will disable the DSS operation (VCC > 10 V).
Overload Operation
Figure 21. A Simple Bipolar Transistor Totally Disables the IC Power Dissipation
The SOIC package offers a 178C/W thermal resistor. Again, adding some copper area around the PCB footprint will help decreasing this number: 12 mm x 12 mm to drop RJA down to 100C/W with 35 mm copper thickness (1 oz) or 6.5 mm x 6.5 mm with 70 mm copper thickness (2 oz). As one can see, the designer must be cautious when using the SO-8 package to check if its thermal performance is compatible with the total power dissipation. The power dissipation is simply Vbulk (high line) x IDSS,AVG. The IDSS,AVG parameter can be measured by inserting an amp-meter in series with the HV pin and compute its average value. We therefore recommend the insertion of a resistor from the bulk connection to the HV pin. This will help to: 1. Avoid negative spikes at turn-off on the HV pin (see below) 2. Split the power budget between this resistor and the package. The resistor is calculated by leaving at least 50 V on pin 8 at minimum input voltage (suppose 100 Vdc in our case):
V * 50 V Rdrop v bulkmin t 7.1 kW . 7.0 mA
The power dissipated by the resistor is thus:
Pdrop + + + VdropRMS2 Rdrop (IDSS @ Rdrop @ DSSduty-cycle)2 Rdrop (7.0 mA @ 7.1 kW @ 0.286) 2 7.1 kW
In applications where the output current is purposely not controlled (e.g. wall adapters delivering raw DC level), it is interesting to implement a true short-circuit protection. A short-circuit actually forces the output voltage to be at a low level, preventing a bias current to circulate in the optocoupler LED. As a result, the FB pin level is pulled up to 4.2 V, as internally imposed by the IC. The peak current setpoint goes to the maximum and the supply delivers a rather high power with all the associated effects. Please note that this can also happen in case of feedback loss, e.g. a broken optocoupler. To account for this situation, NCP1308 hosts a dedicated overload detection circuitry. Once activated, this circuitry imposes to deliver pulses in a burst manner with a low duty-cycle. The system recovers when the fault condition disappears. During the startup phase, the peak current is pushed to the maximum until the output voltage reaches its target and the feedback loop takes over. This period of time depends on normal output load conditions and the maximum peak current allowed by the system. The timeout used by this IC works with the VCC decoupling capacitor: as soon as the VCC decreases from the VCCOFF level (typically 12 V) the device internally watches for an overload current situation. If this condition is still present when the VCCON level is reached, the controller stops the driving pulses, prevents the self-supply current source to restart and puts all the circuitry in standby, consuming as little as 330 mA typical (ICC3 parameter). As a result, the VCC level slowly discharges toward 0. When this level crosses 5.3 V typical, the controller enters a new startup phase by turning the current source on: VCC rises toward 12 V and again delivers output pulses at the VCCOFF crossing point. If the fault condition has been removed before VCCON approaches, then the IC continues its normal operation. Otherwise, a new fault cycle takes place. Figure 22 on the following page shows the evolution of the signals in presence of a fault.
+ 99.5 mW
http://onsemi.com
11
NCP1308
VCC REGULATION OCCURS HERE LATCHOFF PHASE
12 V 10 V 5.3 V
TIME DRV DRIVER PULSES TIME INTERNAL If the fault is relaxed during the VCC natural fall down sequence, the IC automatically resumes. If the fault still persists when VCC reached VCCON, then the controller cuts everything off until recovery.
FAULT FLAG
FAULT IS RELAXED STARTUP PHASE FAULT OCCURS HERE
TIME
Figure 22. Soft-Start
The NCP1308 features an internal 1ms soft-start to soften the constraints occurring in the power supply during startup. It is activated during the power on sequence. As soon as VCC reaches VCCOFF, the peak current is gradually increased from nearly zero up to the maximum clamping level (e.g. 1.0 V). The soft-start is also activated during the over current burst (OCP) sequence. Every restart attempt is followed by a soft-start activation. Generally speaking, the soft-start will be activated when VCC ramps up either from zero (fresh power-on sequence) or 5.3 V, the latchoff voltage occurring during OCP.
Calculating the VCC Capacitor
must be less than the time needed to discharge from 12 V to 10 V, otherwise the supply will not properly start. The test consists in either simulating or measuring in the lab how much time the system takes to reach the regulation at full load. Let's suppose that this time corresponds to 6ms. Therefore a VCC fall time of 10 ms could be well appropriated in order to not trigger the overload detection circuitry. If the corresponding IC consumption, including the MOSFET drive, establishes at 1.6 mA (e.g. with a 10 nC Qg), we can calculate the required capacitor using the following formula: Dt + DV @ C, with V = 2 V. Then i for a wanted t of 10 ms, C equals 9 mF or 22 mF for a standard value. When an overload condition occurs, the IC blocks its internal circuitry and its consumption drops to 330 mA typical. This happens at VCC = 10 V and it remains stuck until VCC reaches 5.3 V: we are in latchoff phase. Again, using the calculated 22 mF and 330 mA current consumption, this latchoff phase lasts: 313 ms.
As the above section describes, the fall down sequence depends upon the VCC level: how long does it take for the VCC line to go from 12 V to 10 V? The required time depends on the startup sequence of your system, i.e. when you first apply the power to the IC. The corresponding transient fault duration due to the output capacitor charging
http://onsemi.com
12
NCP1308
Protecting Pin 8 Against Negative Spikes
As any CMOS controller, NCP1308 is sensitive to negative voltages that could appear on its pins (Figure 23). To avoid any adverse latchup of the IC, we strongly recommend to insert a resistor in series with pin 8. This
resistor prevents from adversely latching the controller in case of negative spikes appearing on the bulk capacitor during the power-off sequence. Please refer to the power dissipation section of this data sheet to see how to calculate this element.
Vbulk Vcc
Latch!
Vbulk <0
Figure 23. A negative spike can occur at mains switch-off if the quality coefficient of Cbulk-Lp is high enough.
Another option consists in adding a diode (or two in series for safety) from the VCC to the bulk capacitor. Figure 12 details this other option:
1 + Cbulk 2 3 4
8 7 6 5 +
1N4007 or
1N4007
1N4007 CVCC
Figure 24. A diode will force the VCCto decrease at the same pace the bulk capacitor does, avoiding a negative ringing on the HV pin.
http://onsemi.com
13
NCP1308
Operation Shots
Below are some oscilloscope shots captured at Vin = 120 VDC with a transformer featuring a 800 mH primary inductance:
Figure 25. This plot gathers waveforms captured at three different operating points: 1st Upper Plot: Free run, valley switching operation, Pout = 26 W. 2nd Middle Plot: Min Toff clamps the switching frequency and selects the second valley. 3rd Lowest Plot: The skip slices the second valley pattern and will further expand the burst as Pout goes low.
Vgate (5 V/div)
Vrsense (200 mV/div)
200 mA x Rskip
Current Sense Pin (200 mV/pin)
Figure 26. This picture explains how the 200 mA internal offset current creates the skip cycle level.
http://onsemi.com
14
NCP1308
VCC (5 V/div)
Vgate (5 V/div)
Figure 27. The short-circuit protection forces the IC to enter burst in presence of a secondary overload.
http://onsemi.com
15
NCP1308
PACKAGE DIMENSIONS
SOIC-8 DR SUFFIX CASE 751-07 ISSUE AG
-X- A
8 5 NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSION A AND B DO NOT INCLUDE MOLD PROTRUSION. 4. MAXIMUM MOLD PROTRUSION 0.15 (0.006) PER SIDE. 5. DIMENSION D DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.127 (0.005) TOTAL IN EXCESS OF THE D DIMENSION AT MAXIMUM MATERIAL CONDITION. 6. 751-01 THRU 751-06 ARE OBSOLETE. NEW STANDARD IS 751-07. MILLIMETERS MIN MAX 4.80 5.00 3.80 4.00 1.35 1.75 0.33 0.51 1.27 BSC 0.10 0.25 0.19 0.25 0.40 1.27 0_ 8_ 0.25 0.50 5.80 6.20 INCHES MIN MAX 0.189 0.197 0.150 0.157 0.053 0.069 0.013 0.020 0.050 BSC 0.004 0.010 0.007 0.010 0.016 0.050 0_ 8_ 0.010 0.020 0.228 0.244
B
1 4
S
0.25 (0.010)
M
Y
M
-Y- G C -Z- H D 0.25 (0.010)
M SEATING PLANE
K
N
X 45 _
0.10 (0.004)
M
J
ZY
S
X
S
DIM A B C D G H J K M N S
SOLDERING FOOTPRINT*
1.52 0.060
7.0 0.275
4.0 0.155
0.6 0.024
1.270 0.050
SCALE 6:1 mm inches
*For additional information on our Pb-Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D.
ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. "Typical" parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT: N. American Technical Support: 800-282-9855 Toll Free Literature Distribution Center for ON Semiconductor USA/Canada P.O. Box 61312, Phoenix, Arizona 85082-1312 USA Phone: 480-829-7710 or 800-344-3860 Toll Free USA/Canada Japan: ON Semiconductor, Japan Customer Focus Center 2-9-1 Kamimeguro, Meguro-ku, Tokyo, Japan 153-0051 Fax: 480-829-7709 or 800-344-3867 Toll Free USA/Canada Phone: 81-3-5773-3850 Email: orderlit@onsemi.com ON Semiconductor Website: http://onsemi.com Order Literature: http://www.onsemi.com/litorder For additional information, please contact your local Sales Representative.
http://onsemi.com
16
NCP1308/D

▲Up To Search▲

Price & Availability of NCP1308DR2G

	To Download NCP1308DR2G Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .